Friday, September 26, 2008

IP Plotter

One of my friend Prashant has developed a good tool whcih actually plots the ip address to find the lacation.

Good tool



regards
shivlu

Click Here To Read Rest Of The Post...

Cisco Vulnerablity

Hi All

We were facing a problem on 18th September and one of my friend Sanjay checked with the help of sanity and found the results given

Buffer information for Small buffer at 0xD809340

  data_area 0x789AD184, refcount 0, next 0xD13D8B8, flags 0x0

  linktype 0 (None), enctype 0 (None), encsize 14, rxtype 1

  if_input 0x0 (None), if_output 0x0 (None)

  inputtime 1d09h (elapsed 00:00:00.320)

  outputtime 1d09h (elapsed 00:00:18.580), oqnumber 65535

  datagramstart 0x789AD1CA, datagramsize 62, maximum size 260

  mac_start 0x789AD1CA, addr_start 0x789AD1CA, info_start 0x0

  network_start 0x789AD1D8, transport_start 0x789AD1EC, caller_pc 0x29596C


Code that exploits a recently revealed flaw in Cisco's router operation system is publicly available, so now it's up to network administrators to patch their systems or face attack.

There have been isolated reports over the weekend of attackers trying to exploit the vulnerability, which is in Cisco's network operating system, IOS, when processing IP version 4 (IPv4) packets. More than 100 of Cisco's products are susceptible including routers and switches.

ISPs are taking the flaw seriously and are patching their systems. "We have not seen the huge blackouts that would have occurred if they hadn't started to address the issue," said Dave Cole, director of products at Foundstone Inc., Mission Viejo, Calif. "The urgency to patch systems has certainly increased because the exploit is now available."

The Computer Emergency Response Team at Carnegie Mellon University in Pittsburgh has issued an advisory because the exploit code was posted to some Internet mailing lists. Symantec and Internet Security Systems have both raised their threat levels for the vulnerability because of the code's release.

In general, the release of exploit code increases the danger of vulnerabilities as it allows people with limited technical savvy to take advantage of the flaws. Instead of having to write the precise packets needed to attack the flaw, a would-be attacker would only have to cut and paste the information from the Internet. In the case of the Cisco vulnerability, exploiting it would trigger a denial-of-service attack that could shut down Web sites and network access points.

Exploiting the vulnerability requires sending some specially crafted IPv4 packets to affected systems. The packets would trick the systems into thinking they are full. The routers and switches would then stop processing traffic, which would render Web servers and other network-dependent systems inaccessible.

The release of the exploit code wasn't surprising given the fact that advisories give would-be attackers the information they need to create the code, Cole said. "The real question is whether people would have enough time to perform upgrades to their systems."


After that he informed to the cert and on 24th september we found the same bug on cisco which is affecting the given IOS.

The vulnerability affects Cisco IOS-based routers and switches running 11.x thru 12.2.x. IOS version 12.3 and a number of 12.1 and 12.2 rebuilds are not affected


regards

shivlu


Click Here To Read Rest Of The Post...

Monday, September 22, 2008

MVPN Problem

During the analaysis of one of our client network running MPLS in the core and having lot of customers which are on MVPN. Core is using sparse-dense mode but with no RP and customers are using static RP mapping. The main disadvantages of using this type of topology is that if the core wonot be able to find the RP then it will fall back to the dense mode. So in the scenarios where no RP is defined will alwasy fall back to the dense mode which means unnecessary flooding of stream to each and every vrf which is the part of that VPN. By using this the main problem is that data mdt can never converge in the VPN, it it means if you are using data mdt then there is no use of that becasue your tree is *,G and data mdt is for S,G; It means never S,G entry will come and data mdt will never converge. To overcome the problem need to define the RP address in the core & RP should be specifically for the data MDT groups. RP can be defined by using AUTO-RP or BSR.



Click Here To Read Rest Of The Post...